Tools You Need to Set Up a New Bathtub
Tools You Need to Set Up a New Bathtub
Blog Article
Presented here down the page you'll find some dependable content related to Installing A Bathtub.
Setting up a tub isn't specifically rocket science, however it does need strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the job can move immediately; if you need to open a wall to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to hiring a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a new bathtub in your restroom if you have already bought a brand-new bathtub and also do not require to alter the plan of your previous water system pipes.
Your tools and product list must make up the following:
Preparing for the Installation
To start with, the sustaining framework supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be quite troublesome due to the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the tub ought to wait up until the tub has been used at least once as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in position with the maker offered backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The previous type should be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, bring about issues with wetness and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our topic on Tools You Need to Install a New Bathtub . Thank you so much for taking the time to read our blog post. Do you know another person who is serious about the niche? Feel free to share it. I enjoy reading our article about Tools You Need to Install a New Bathtub .
This Site
Report this page